![]() Of course, one would not expect a good match since the standard continuous-time PID block provided by Xcos does not have a filter in the derivative term. Notice that the step responses from the continuous (green) and discrete (red) PID controllers do not match, though they bear quite similar behavior.įigure 4 response comparison between the continuous and discrete PID Running the simulation yields the result in Figure 4. Then the second and third terms from the controller expression in (10) is inputted to the DLR blocks for integral and derivative as shown in Figure 2 and 3, respectively. Ts = 0.01 // must match sampling period used in simulation N = 20 įigure 1 dpidsim.zcos continuous versus discrete PID simulation Kp = 200 // these are values obtained from ZNFD tuning Note that the controller is assembled from Xcos gain blocks, and the DLR blocks from discrete-time systems palette. Add the second feedback loop with discrete-time PID controller as shown in the Xcos diagram in Figure 1, or download dpidsim.zcos. The plant consists of a robot joint driven by DC motor and a LPF at its input. We will use the setup in Figure 10 from our Module 4: PID Control. We want to simulate how this controller performs compared to its continuous-time version. Obviously for all the terms above, the sampling period affects the gains of integral and derivative terms.Īs an example, suppose we use backward Euler methods for both the integral and derivative terms, the resulting discrete-time PID controller is represented by Similarly, the derivative term in (3) can be discretized as Given a sampling period Ts ,the integral term Ki/s can be represented in discrete-from by There are commonly 3 variations to do so, by means of forward Euler, backward Euler, and trapezoidal methods. It is quite common to modify the derivative term to an LPF filter, to make it less noisyĪ straightforward way to discretize this controller is to convert the integral and derivative terms to their discrete-time counterpart. In this article we investigate such relationship on a commonly-used PID form.įor the continuous-time PID, we start with the so-called parallel form In practice, we may want to relate a chosen set of parameters in continuous-time, perhaps from simulation or some tuning rule, to its discrete-time representation. In that article, we simplify the matter by omitting the effect of sampling period on the PID parameters. In our previous article Digital PID Controllers, we discussed some basics of PID controller implementation as software algorithm on a computer. Part I: Discrete PID Gains as Functions of Sampling Time Make sure it matches the one used on Arduino to ensure correct time scale on the plot.This content was kindly contributed by Dew Toochinda, the Scilab Ninja, and originally posted on In the Scilab stepplot() function (discussed on page 139 of Chapter 6), sampling period T is hard coded on the second line of the function. ![]() The rate of Serial Monitor or UNO Command Window must be changed to match. Later on when the controller is more complicated, performance suffers with slow serial communication speed so it is increased to 115200 bps. At the beginning of the book, the baud rate is set as 9600 bps. If you receive strange characters, check the serial baud rate.In such case, close all windows and close serial port by the following commands Otherwise, it could happen easily that UNO Command Window loses focus and froze. Close all graphic windows before you run the UNO Command Window.Flexible eXperiments (FX) Sketch for Arduino UNOįCSA_sw.zip : all Scilab and Arduino examples used in the book. Linear Continuous-time Systems and Feedback Properties.I actually use this book to accompany my engineering teaching at Kasetsart university.įree samples (Chapter 1,2, and Appendix A, B) can be downloaded by clicking on the links below. To be readable as a book, all contents have to be wrapped to a cohesive story that can serve as classroom supplement. Some materials are already scattered around my website scilab.ninja, while others, such as most topics on Arduino, are entirely new. Since my research interests are in control systems area, the focus is on control analysis, design, simulation, and then implementation on a target board. The purpose of this e-book is to guide the audience from basic usage of Scilab and its simulation engine Xcos, to prototyping on an Arduino board. Title : Feedback Control with Scilab and Arduino.
0 Comments
Leave a Reply. |